The objective is to determine how lubricant ch48ce may influence bearing life calculations. temperature for mineral, PAO and PAG lubricants is presented here. Hopefully, this data provides insight into when and why we would rightfully expect to see reductions in frictional conditions leading to improved reliability and energy savings as a consequence of changing to a synthetic-based lubricant.Ĭlearly, it is not always best to use a synthetic lubricant.Ī study comparing EHL film thickness vs. ![]() Much is made of the potential benefit of synthetics for energy conserving purposes. However, as the temperature changes, the relationship changes, leaving us with clear direction for when we could expect to see which synthetics demonstrate superior film-forming capability in a temperature range. Note in particular the performance level comparison for temperatures below 80☌. The analysis suggests that there are in fact conditions where the mineral oil out-performs the PAO/PAG synthetics. The actual unit of measure (mm 2/N) is less useful than the percentage improvement of the synthetics over the mineral oil at the given temperature points as noted in the information sheet. The pressure-viscosity coefficient gives us fixed values for lubricant film thickness in a given set of conditions (elastohydrodynamic regime, also known as an EHL or EHD regime) based on a mathematical estimation as noted in the American Gear Manufacturers Association (AGMA) Information Sheet AGMA 925-A03 (see Note). The pressure-viscosity coefficient refers to the relationship between the load placed on the oil film (pressure) at the dynamic load zone and the thickness of the oil film (viscosity) at that load, when all other factors (material, temperature, geometry, speed, load) are constant. Terrific for bamboo cutting boards, serving trays, utensils, drawer organizers, bowls, well.you get it, anything bamboo.Are synthetic oils (PAO - Polyalpha olefin and PAG - Polyalkylene glycol) better gear and bearing lubricants than mineral oils?Īt the heart of the issue is a property we refer to as pressure-viscosity coefficient of the various types of lubricant base oils. Maintain your often overlooked wooden utensils, salad bowls, serving trays and pizza peels. Hardwood counter tops and islands are not only provide a stunning look to your kitchen, they are functionally magnificent and will continue to wow with regular care Safest butcher block oil on the market with ingredients that exceed thee United States FDA regulations on safety for direct and indirect contact with food.īutcher blocks need a VERY low viscosity oil that penetrates deep because of the thickness of the wood Oiling cutting boards or butcher blocks every 3-4 weeks helps prevent wood from drying, splitting or cracking.ĬLARK'S Oil will never go rancid or harbor germs like plant-based oils. Perfectly blended with organic natural lavender and rosemary oils. Oil works its way deep into the grain of your wood surfaces. CLARK'S is obsessed with healthy eating which is why our oil exceeds the FDA regulation on food safety and will never go rancid or harbor germs like plant-based oils.Īpply a generous amount of oil evenly to the wood surface and allow it to penetrate for 1-2 hours. Your cutting board or butcher block is also soaking up everything it touches (good and bad), that's why you need cutting board oil with anti-microbial properties to penetrate deep into the wood to block bad bacteria from entering the wood fibers. Wood naturally wants to absorb everything it can. ![]() This is when a good conditioning oil is needed. Between sharp knives, water, soap, and temperature fluctuation, wood begins to dull, warp, and show wear. Kitchen surfaces and tools take a beating. A few moments of work will bring a lifetime of joy with your wood treasures! ![]() Whether it's Granddad's butcher block, the cutting board you received as a wedding present, a wooden salad bowl you picked up at the market, or an end-grain counter top at your very own restaurant, you take pride in making sure they are all well maintained. CLARK'S Cutting Board Oil is a delightfully scented formula that’s easy to apply and works beautifully to restore and revive your wood surfaces.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |